Yours Fav Shopping Stop!!

Wednesday, 5 November 2014

Library Exchange Format (LEF)

Library Exchange Format (LEF) is a specification for representing the physical layout of an integrate circuit in an ASCII format. It includes design rules and abstract information about the cells. LEF is used in conjunction with Design Exchange Format (DEF) to represent the complete physical layout of an integrated circuit while it is being designed.

An ASCII data format, used to describe a standard cell library Includes the design rules for routing and the Abstract of the cells, no information about the internal netlist of the cells

A LEF file contains the following sections:

�� Technology: layer, design rules, via definitions, metal capacitance
�� Site: Site extension
�� Macros: cell descriptions, cell dimensions, layout of pins and blockages, capacitances.

The technology is described by the Layer and Via statements. To each layer the following  attributes may be associated:
�� type: Layer type can be routingcut (contact), masterslice (poly, active),overlap.
�� width/pitch/spacing rules
�� direction
�� resistance and capacitance per unit square
�� antenna Factor

Layers are defined in process order from bottom to top


poly masterslice
cc cut
metal1 routing
via cut
metal2 routing
via2 cut
metal3 routing

Cut Layer definition


LAYER
 layername
TYPE CUT
;
SPACING
Specifies the minimum spacing allowed between via cuts on the same net or different nets. This value can be overridden by the SAMENET SPACING statement (we are going to use this statement later)END layerName 

Implant Layer definition

LAYER layerName
TYPE IMPLANT ;
SPACING minSpacing
END layerName
Defines implant layers in the design. Each layer is defined by assigning it a name and simple spacing and width rules. These spacing and width rules only affect the legal cell placements. These rules interact with the library methodology, detailed placement, and filler cell support.

Masterslice or Overlap Layer definition

LAYER layerName
TYPE {MASTERSLICE OVERLAP} ;
Defines masterslice (nonrouting) or overlap layers in the design. Masterslice layers are typically polysilicon layers and are only needed if the cell MACROs have pins on the polysilicon layer.

Routing Layer definition

LAYER layerName
TYPE ROUTING ;
DIRECTION {HORIZONTAL VERTICAL} ;
PITCH distance;
WIDTH defWidth;
OFFSET distance ;
SPACING minSpacing;
RESISTANCE RPERSQ value ;
Specifies the resistance for a square of wire, in ohms per square.  The resistance of a wire can be defined as RPERSQU x wire length/wire width
CAPACITANCE CPERSQDIST value ;
Specifies the capacitance for each square unit, in picofarads per square micron. This is used to model wire-to-ground capacitance.

Manufacturing Grid

MANUFACTURINGGRID value ;
Defines the manufacturing grid for the design. The manufacturing grid is used for geometry alignment. When specified, shapes and cells are placed in locations that snap to the manufacturing grid.

Via

VIA viaName
DEFAULT
TOPOFSTACKONLY
FOREIGN foreignCellName [pt [orient]] ;
RESISTANCE value ;
{LAYER layerName ;
{RECT pt pt ;} ...} ...
END viaName
Defines vias for usage by signal routers. Default vias have exactly three layers used:
 A cut layer, and two layers that touch the cut layer (routing or masterslice). The cut layer rectangle must be between the two routing or masterslice layer rectangles.

Via Rule Generate

VIARULE viaRuleName GENERATE
LAYER routingLayerName ;
DIRECTION {HORIZONTAL VERTICAL} ;
OVERHANG overhang ;
METALOVERHANG metalOverhang ;
ENCLOSURE overhang1 overhang2 ;}
LAYER routingLayerName ;
DIRECTION {HORIZONTAL VERTICAL} ;
OVERHANG overhang ;
METALOVERHANG metalOverhang ;
ENCLOSURE overhang1 overhang2 ;}
LAYER cutLayerName ;
RECT pt pt ;
SPACING xSpacing BY ySpacing ;
RESISTANCE resistancePerCut ;
END viaRuleName
Defines formulas for generating via arrays. Use the VIARULE GENERATE statement to cover special wiring that is not explicitly defined in the VIARULE statement.

Same-Net Spacing

SPACING
SAMENET layerName layerName minSpace [STACK] ; ...
END SPACING
Defines the same-net spacing rules. Same-net spacing rules determine minimum spacing between geometries in the same net and are only required if same-net spacing is smaller than different-net spacing, or if vias on different layers have special stacking rules.
Thesespecifications are used for design rule checking by the routing and verification tools.
Spacing is the edge-to-edge separation, both orthogonal and diagonal.

Site

SITE siteName
CLASS {PAD CORE} ;
[SYMMETRY {R90} ... ;] (will discuss this later in macro definition)
SIZE width BY height ;
END siteName

Macro

MACRO macroName
[CLASS
COVER [BUMP]
RING
BLOCK [BLACKBOX]
PAD [INPUT | OUTPUT |INOUT | POWER | SPACER | AREAIO]
CORE [FEEDTHRU | TIEHIGH | TIELOW | SPACER | ANTENNACELL]
ENDCAP {PRE | POST | TOPLEFT | TOPRIGHT | BOTTOMLEFT | BOTTOMRIGHT}
}
;]
[SOURCE {USER BLOCK} ;]
[FOREIGN foreignCellName [pt [orient]] ;] ...
[ORIGIN pt ;]
[SIZE width BY height ;]
[SYMMETRY {X | Y | R90} ... ;]
[SITE siteName ;]
[PIN statement] ...
[OBS statement] ...

Macro Pin Statement

PIN pinName
FOREIGN foreignPinName [STRUCTURE [pt [orient] ] ] ;
[DIRECTION {INPUT | OUTPUT [TRISTATE] | INOUT | FEEDTHRU} ;]
[USE SIGNAL | ANALOG | POWER | GROUND | CLOCK } ;]
[SHAPE {ABUTMENT RING FEEDTHRU} ;]
[MUSTJOIN pinName ;]
{PORT
[CLASS {NONE CORE} ;]
{layerGeometries} ...
END} ...
END pinName]

Macro Obstruction Statement

OBS
LAYER layerName [SPACING minSpacing | DESIGNRULEWIDTH value] ;
RECT pt pt ;
POLYGON pt pt pt pt ... ;
END

No comments:

Post a Comment